K6부터 극한의 오버클럭 AMD의 매력에 푹 빠져 듀론, 썬더, XP, 바톤을 지나
지금은 체인텍 VNF250 과 AMD Athlon64 2800을 사용중이다. 과거의 AMD하면 인텔의 그늘에
가려 인텔이 휩쓸고간 자리를 저가격으로 시장을 잠식하던 모습만이 남아있다. 하지만
K6부터 기술적인 우위를 점하던 인텔을 추격하고 현재는 동등한 입장에서 인텔의 동급CPU보다
저렴하고 발열까지 적어 오버클럭에 자유로운 모습으로 태어난 AMD.
아마도 지금 인텔사용자나 AMDXP사용자중에서 샘프론이나 애슬론64로 업그레이드
하려고 마음은 먹고 있지만 과연 업그레이드한 효과를 느낄 수 있을까 하는 의구심 때문에
쉽게 결정을 내리지 못하신 분들이 많을것이라 생각된다. 물론이겠지만 인텔의 사용자의 경우는
기존 플래폼을 버린다는게 결코 쉬운일은 아니기 때문이다. 본 필드테스트는 이런 부분에서
약간의 도움이나마 드리고자 기존 사용자들이 업그레이드를 했을 경우에 컨셉을 맞추고자한다.
본문에 자세히 설명하겠지만 아시다시피 본 제품은 디앤디컴에서
제공한 K8A8X-M으로 ALI M1689칩셋을 사용한 M-ATX용 보드이므로 미니케이스나 M-ATX용 슬림케이스를
이용하시는 분이라면 본 필드테스트를 좀 더 눈여겨 봐주시길 바라며 본 필드테스트를 시작할까한다.
그럼 허접하나마 본 필자의 소개와 테스트에 사용된 시스템의 간략한 스펙을 소개한다.
필자는 4년차 소프트웨어 개발자로 PHP/JSP 사이트 구축, 산업용 장비를 이용한 데이터 송수신 및
출력 표시기 어플리케이션, 광양 무선 AccessPoint LF진동시스템 등의 프로젝트 경험있고, 컴퓨터는
대우 IQ1000을 시작으로 x86, 펜티엄 계열, Kx계열 등을 사용했고, 햔 6개월동안 PC조립 A/S등의
경력도 가지고 있고 필드테스트는 경력이 화려하거나 하지는 않지만 과거 나우누리 PUG(Power
User Group)등에서 활동했으며, MS의 WinXP 베타버전 테스터로 활동 (5위)에 입선(?)했으며,
최근엔 다나와/디비나와 공동제공 게인워드 Hollywood@Home 7.1 사운드카드 필드테스트에서 최우수로
선정될 정도로 항상 뭔가 시작하면 열심히 하는편이라고 자부한다.
The M1689 is ALi's new generation super single
chipset that offers a high-performance, the highest integration and
cost-effective solution for AMD Hammer microprocessor PC systems.
The M1689 integrates AGP8X controller, AC-Link Host Controller,
2-channel dedicated Ultra-66/100/133 IDE Master controller, USB 2.0/1.1
Host controllers with 8 ports in total, IO APIC controller, 1/10/100
Mb/s Fast Ethernet, SATA, and HyperTransportTM Technology Link
interface. Additional features include Host Signal Processing (HSP)
software modem solution, ACPI support, green function, and Real Time
Clock.
By incorporating USB 2.0 host controller with the data transfer rate up
to 480 Mb/s, the M1689 provides the most advanced connectivity for
higher performance USB devices. 8 USB ports are supported with 1 USB 2.0
EHCI (Enhanced Host Controller Interface) controller and 3 USB 1.1 OHCI
controllers.
The built-in Audio solution in the M1689 is an advanced PCI HSP audio
controller with Scatter-gathering DMA fully supported. The M1689 Audio
is compliant with standard AC97 CODEC and supports 6 audio playback
channels for PCM_out L/R, Surr L/R, Center and LFE, dual PCM inputs and
dual microphone inputs.
The 100BASE-TX/10Base-T Fast Ethernet MAC is fully compliant with PCI
Spec. 2.3 and IEEE802.3u. The MAC provides a direct interface to the PCI
local bus and direct connection to the PHY/transceiver via MII
interface. As a controller, it is bus master capable. The MAC also
supports auto-negotiation function that enables it to detect speed and
duplex automatically. The MAC provides the Power Management capability
that is compliant with the Network Device Class Power Management
Specifications Rev 1.1, ACPI Specifications Rev 2.0, and the PCI Bus
Power Management Interface Specifications 1.1. In addition, it can
support remote Wake-up capability to power up a remote sleeping station
on the network.
The M1689 also provides the best power management solution. The M1689
incorporates ACPI support, deep green function, and 2-channel Ultra
DMA-33/66/100/133 IDE bus master controller, all into one 35mmx35mm BGA
(Ball Grid Array) chip.
Processor Support
Supports AMD Opteron, Athlon 64, Mobile Athlon 64 processors.
Supports HyperTransport Technology I/O.
Provides a High Integration Bridge
(with Audio, HSP Modem, LAN, USB, IDE)
between HyperTransport Technology I/O Link Bus, AGP bus, PCI Bus
and Peripheral Bus for Desktop and Notebook Systems
Accelerated Graphics Port (AGP) Interface
Compliance
with AGP 3.0 specification signaling, supporting 4x and 8x
transfer rates.
Compliance with AGP 2.0 specification 1.5
volt signaling, supporting 1x, 2x, and 4x data-transfer modes.
Supports up to 32 outstanding requests.
HyperTransport Technology (HTT) I/O Link
HyperTransport Technology I/O Link Protocol
Meets the v1.05 Specification
16-bit HTT downstream link & 8-bit upstream
link @ 800MHz
HTT supports transfer rates of 1600, 1200,
800, and 400 mega-transfers per
second.
Maximum bandwidth is 3.2 gigabytes per
second downstream and 1.6 gigabytes per second upstream
Independent transfer rate and bit width
selection for each side.
PCI Interface
Supports PCI Master and Slave Interface
PCI spec. 2.3 Compliant
PCI Power Management Interface spec. 1.1
Compliant
Supports up to 7 PCI Masters
Supports programmable PCI arbitration
priority of PCIREQ#/PCIGNT#
Provides Steerable PCI Interrupts for PCI Device Plug-and-Play
Enhanced DMA Controller
Provides 7 Programmable Channels, 4 for
8-bit Data Size, 3 for 16-bit Data
Size
32-bits addressing capability
Counter/Timers
Provides 8254 Compatible Timers for System
Timer, Refresh Request, Speaker Output Use
Full Support for ACPI and OS Directed Power
Management
Full Support for Instantly Available PC
feature
CPU SMM Legacy Mode and SMI Feature
Supported
Full Support of Clock Control Functions
Supports I/O Trap for I/O Restart Feature
PMU Operation States :
1. G0 State
-- On
-- Standby Mode
2. G1 State (Suspend Mode 1)
-- S1 State (Power On Suspend)
-- S3 State (Suspend To RAM)
-- S4 State (Suspend To DISK)
3. G2 State (Suspend Mode 2)
-- S5 State (Soft-Off)
4. G3 State (Mechanical-Off)
Legacy Monitor Timers supported
Low Battery timer supported
Provides System Activity Monitoring
Multiple External Wakeup Events
CLKRUN# Function Supported for PCI Mobile
Design Guide Ver1.1
Thermal Alarm Supported
Clock Generator Control Logic Supported
-- CPUCLK Stop Control
-- PCICLK Stop Control
Run Time Events Supported
General Purpose Input Signals, General
Purpose Output Signals and General Purpose Input/Output
Signals Supported
All Registers Readable/Restorable for
Proper Resume from Suspend State
Watch Dog Timer for
-- Set a Bit in Register
-- Generate an SMI#/SCI/NMI/INIT
-- Generate System Reset
Build-in Real Time Clock
Common calendar year with leap year
compensation
Binary or BCD data representation
12/24 hour mode
Daylight saving time option
Interfaces with software as 256 bytes of
RAM
-
15 bytes of clock and control registers
-
241 bytes of general-purpose RAM
Month-of-day alarm
Built-in PCI IDE Controller
Supports Ultra DMA Mode Transfers up to
Mode 6 Timing (100/133 Mbytes/sec)
Supports 48-bit LBA (Large Disk), hard
drive larger than 137 GB
Supports PIO Modes up to Mode 4 Timings,
and Multiword DMA Mode 0,1,2 with Independent Timing of up to
4 Drives
Dedicated Pins of ATA Interface for each
Channel
Supports Tri-state IDE Signals for Swap Bay
USB Interface
One EHCI USB 2.0 and Three OHCI USB 1.1
Host Controllers for supporting up to eight USB Ports
Supports HS (480Mbits/sec), FS
(12Mbits/sec) and LS (1.5Mbits/sec) data transfer rate
Supports system wake up from S1 ¡V S4
Supports Legacy Keyboard and Mouse
emulation in DOS environment
Low Pin Count (LPC Rev1.1) Interface
Supports LPC interface for legacy devices
Supports 2 LPC Master and 7 DMA devices
Supports TPM (Trusted Platform Module)
SMBus Interface
System Management Bus Interface Meets the
v2.0 Specification.
Support SMBALERT#.
Audio System
Fully Plug-and-Play PCI controller and
software
PCI 2.3 compliant bus master optimized for
multiple stream operation
Scatter-gathering
support
Dual PCM inputs and dual microphone inputs
support
6 audio playback channels: PCM_out L/R,
Surr L/R, Center and LFE
20-bit sample resolution support
Up to 3 AC97 SDATA_IN pins support ¡V 3
codecs (2 for audio and 1 for modem)
Software
Modem Interface
The M1689 provided the AC'97 2.3 compliant
digital controller interface for third parties (such as the AMC Codec¡¦s vendor) to enable the software modem solution.
2 separate telephony bus master channels.
One for modem output, one for modem input..
AC'97 2.3 Modem variable sample rate
support for ¡”On Demand¡¨ sample transport scheme.
AC'97 2.3 GPIO pin status and control
support.
Power Management and wake-up event support
Caller ID string transmission via AC-link
support
1/10/100
Mb/s Fast Ethernet MAC
The M1689 will provide the 1/10/100 Mbps
Media Access Control (MAC) controller for the best solution of
the phone-line/Ethernet LAN connectivity.
Compliant
with IEEE 802.3u 100BASE-TX, IEEE 802.3 10BASE-T standard
PCI interface controller fully compliant
with PCI specification 2.3
EEPROM interface to store configuration
information and user defined message
Two large independent receive FIFO (2K) &
transmit FIFO (2K) with programmable FIFO threshold and full
packet burst processing
Support automatic packet deletion for runt
packets and packet re-transmission with no FIFO reload
Support Full/Half Duplex operation
Physical, broadcast address recognition and
512-bit hash table algorithm for multicast address filtering
Compliant with the Advanced Configuration
and Power Interface Specification (ACPI) Revision 2.0
Compliant with the Network Device Class
Power Management 1.0
Compliant with PCI Bus Power Management
Interface specification 1.1
Compliant with IEEE802.3u Auto-negotiation
protocol for automatic link type selection
WFM 2.0 compliance
Serial ATA Host Controller
Supports SATA 1.0 (High Speed Serialized AT
Attachment, Revision 1.0), 1.5 Gb/s data rate.
Supports Host adapter register interface (SCR,
Status and Control Registers).
에거에거 어려운 영문 스펙보시느라 힘들었을 것으로 생각된다. 나름대로 깔끔하게 정리한다고 했는데 역시나 영문에 까막눈인 필자로써는 정리하는것도 힘들었다. 그러니 애교로 바주시길 바란다. 물론 영어를 너무 잘하시고, 시간이 남는분은 해석하셔서 저에게 주시면 깔끔한 한글문서로 정리할 용의도 있다. ^^;
이번장에서는 경쟁사 및 동급이라 취급되는 제품들의 스펙과 제품에 함께 제공되는 패키지상태으로 비교테스트
하려한다. 물론 현재 보유중인 제품은 체인텍의 VNF250뿐이기 때문에 성능비교까진 할 수 없겠지만 기본 제공되는 품목과 가격만으로도 만족도 조사는 충분한 몫을 한다고 생각된다. 본 필자가 알고 비슷한 수준이라고 거론되는 AMD 754지원 보드중에서 대표격인 제품으로 선택했다. 비교 테스트할 제품은 K8A8X-M(ALI), 체인텍 VNF250(nForce3), ABIT KV8Pro(VIA)이고 다시한번 말씀드리지만 본 필자가 아는 수준에서 뽑은 비슷한 가격대의 메인보드이므로 이에 따른 태클은 사양한다. 사실 ABIT KV8Pro는 가격으로 따지면 분명 비교가 불가(?)한 제품인건 알고 있으나 제품군의 한계때문에 어쩔 수 없는 선택이었고 이는 비교시 반드시 반영할것을 약속한다.
2.1 스펙비교
구분
K8A8X-M
VNF250
KV8Pro
CPU
AMD 754제품군
메인칩셋
ALi M1689
nForce3-250
K8T800Pro+VT8237
FSB
800MHz
800MHz
1GHz
지원 메모리
DDR266/333/400
DDR266/333/400
DDR266/333/400/
최대메모리
2GB
2GB
2GB
AGP
4x / 8x
4x / 8x
4x / 8x
PCI / CMR
2 / 0개
5 / 1개
5 / 0개
USB
USB2.0 8개
USB2.0 8개
USB2.0 4개
HDD지원
ATA-133
ATA-133
ATA-133
SATA/RAID
ALi M1689 2채널
nForce3-250 2채널
Via VT8237 2채널
LAN
Realtek 8201BL(100Mbit)
Realtek 8100C(100Mbit)
VIA VT6122 (1GBit)
사운드지원
CMI 9761A 6Ch
CMI 9761A 6Ch
ALC658 6Ch
SPDIF
미지원
지원
지원
폼팩터
m-ATX
ATX
ATX
특징
m-ATX 타입지원
CMCard를 통해 광출력지원
8bit Debug LED탑재
uGuru 칩셋(Winbond社의 W83L950D)장착으로 6가지기능을 총괄하여 관리가 가능
비교는 위 표와 같다. 보시는바와 같이 기본 지원 스펙으로는 별반 차이점을 느낄 수 없다. 하지만 약간 특이한점이라면 일반적으로 m-ATX 타입의 메인보드가 PCI를 3개정도 지원하고 있는데 반해 PCI슬롯이 2개라는 점이 특징이고 요즘처럼 컴퓨터의 AV기기화 현상에 비한다면 PCI슬롯 부족과 광출력 미지원하고 있다는 점이다.
m-ATX의 경우 대부분이 슬림PC나 베어본 스타일에 탑재되기 때문에 이에 준해 그래픽코어를 내장하거나 최대한 크기를 줄이고 모든부분에서 지원하기 위한 노력을 기울이고 있다. 하지만 요즘처럼 컴퓨터가 AV기기를 대체하고 있는 상황에서 PCI슬롯과
광출력 지원여부는 큰 관심사가 아닐 수 없다. 본 필자도 불과 얼마전까지만해도 TV수신카드와 추가랜카드(공유를위한), 내장사운드의 한계로 인한 PCI 사운드카드, 광출력 브라켓을 사용했었다. 이것만으로도 이미 슬롯은 부족하게 된다. 간단하게 내장사운드를 사용하지 않고 TV수신카드를 가지고 있는 유저라면 이미 다음 추가 업그레이드는 불가하다는것이다. 물론 내장사운드를 사용하면 되겠지만 광출력을 지원하고 있지 않기 때문에 이는 슬롯부족의 문제를 더욱 부추기는 결과를 초래할것이기 때문이다.
AMD하면 일단은 오버클럭을 생각하지 않을 수 없다. 역시나 3개보드 모드 이에 대한 준비를 하고 있다. 하지만 이중에서 가장 돋보이는건 ABIT의 nGuru(일명 구라클럭)을 통해 EQ, OC Guru, Flash Menu, Audio EQ, FanEQ, BlackBox 등의
6가지 관리 기능을 가졌다는것이다.